If your Wi-Fi
connection is crawling along, the first question to ask is whether it’s really
the network that’s to blame. The true culprit could be a specific program or device
clogging up your network perhaps a backup job beaming terabytes of data to your
NAS box, or an infected device that’s been subsumed into a botnet, and is now,
without your knowledge, flooding out malicious datagrams to destinations around
the world.
With free
software such as Wireshark, you can inspect all the data packets on your
network as they fly through the air, and easily discover whether one device is
taking up more than its fair share of bandwidth. Your router’s web-based
administration interface may also offer reports and logs: the way you access
these will differ between models and manufacturers, but they’re well worth
looking at since they’ll also include activity from wired clients.
Don’t assume
that you know about every device on your network: if your network is open, or
has a guessable password, your neighbours or others could be leeching bandwidth
and hoping you won’t notice. You can boot them off, or use your router’s QoS
settings to prioritise the traffic that’s important to you.
If all that
sounds like too much hassle, try simply switching off your network-connected
devices one by one, and keep checking network speed as you go. For obvious
reasons, an online speed-tester isn’t the right tool for this, as results will
be limited by the speed of your internet connection rather than your domestic
wireless network. Don’t trust the wireless link speed reported by Windows
either: this gives an idea of the theoretical throughput of your wireless
connection, but if you’re interested in real-world performance, there’s no
substitute for copying files back and forth between devices. If switching off a
spare PC causes things to suddenly start zipping along, it suggests a
little housekeeping may be all that’s needed to give your wireless network a
boost.
1.
Boost your Wi-Fi: Changing the channel
If you accepted the default settings when
installing your router, your wireless network is probably sending and receiving
data in the 2.4GHz band, and specifically on channel 1, 6 or 11. This means
packets are broadcast and received over a fairly wide radio band, centred on
2,412MHz, 2,437MHz or 2,462MHz.
These frequencies have been a standard
part of the 802.11 wireless protocol since its introduction in 1997 so using
them as defaults ensures that pretty much every Wi-Fi device in your home
(and, indeed, in the world) should be able to talk to the router.
The downside is that if you live in a
dense urban area, such as a block of flats, your neighbours’ networks will be
using these frequencies too, resulting in interference that slows down the
connection for everyone. Other electrical appliances such as cordless phones
and wireless video extenders may use these channels as well. And while
microwave ovens are normally well shielded, these too can generate radio
“noise” at frequencies in the 2.4GHz range, which is highly disruptive to radio
communications.
The simplest answer is to switch your
network to a different frequency. Your router’s settings page should provide a
dropdown allowing you to switch to a different channel within the 2.4GHz
band they’re numbered from 1 to 13. Experiment by changing this to see whether
one end of the spectrum provides a better connection than the other: your
devices should automatically rediscover the network and reconnect soon after
you change the channel.
If you prefer a more methodical approach,
use a free tool such as NirSoft’s WifiInfoView, or a smartphone app such as Wi-Fi
Analyser for Android. These will survey all the wireless networks within
range and their relative signal strengths, so you can avoid them as far as
possible. Remember, though, that such tools won’t show up interference from
other sources; if all your neighbours are avoiding a particular channel,
there may be a reason for this.
2.
Boost your Wi-Fi: Band on the run
If switching channels doesn’t help,
consider hopping to a different frequency band altogether. The 5GHz Wi-Fi band
came into use in 2009 as part of the 802.11n standard, and since there’s less
interference in this band, it may provide better performance. (Strictly
speaking, the 5GHz band had in fact been introduced a decade earlier in the old
802.11a standard, but this never became popular.)
Some older devices may not support 5GHz,
but this isn’t necessarily a showstopper: most routers that support a 5GHz
wireless network will let you run it alongside a regular 2.4GHz network. This
does mean that you’ll have two separate SSIDs to manage, which complicates the
job of administering things, especially if you want to ensure your devices
connect to the right one.
A second possible issue with 5GHz is that
a higher frequency means lesser penetration, so you’re less likely to
experience interference from three doors down but, by the same token, if you’re
trying to extend your network through an interior wall or two, you may find
that the drop-off at 5GHz is barely preferable to the interference at 2.4GHz.
3.
Extending range with a Wi-Fi signal booster
Even if there’s nothing but clear air
between your router and its Wi-Fi clients, location can have a big effect on
signal quality, since wireless links (like all radio transmissions) grow weaker
over distance. If you want to improve the quality of a wireless signal far from
your router such as in a summerhouse at the bottom of your garden a simple
option is to invest in a wireless repeater or a range extender, which you can position
between the two stations to retransmit packets back and forth at full strength.
It’s worth noting that repeaters and
extenders do different jobs. A repeater acts as a rebroadcasting station for
your router, and is effectively invisible to connecting clients. A range
extender, on the other hand, operates a wireless network of its own, and acts
as a bridge between devices connected to this network and your home LAN.
If you want to save money, it’s possible
to set up an old router as a repeater or range extender, although you may need
to dive into technical settings to make it work, and older hardware may
not support the latest high-speed connection technologies. It’s also possible
to configure a PC or Mac to act as an extender; of course, this isn’t a
particularly power-efficient solution, unless you’re using the system for
something else at the same time.
Whichever approach you choose, the
involvement of more hardware and potentially more packets flying through the
air means that network performance might not be as fast as it would be if you
were able to move your PC closer to the router. But it should certainly be
better than an unboosted long-range connection.
4.
Aiming and upgrading your wireless network antennas
We’ve mentioned that walls affect signal
strength, which in turn hinders your connection speed. In fact, almost
everything in your home has an effect on the throughput of your wireless
network: radio transmissions bounce off furniture and other obstructions, so
even when you’re in the same room as your router, there will be pockets of
interference.
There’s no way around this, but you can
make a difference by moving your router, or adjusting the orientation of its
antennas. One useful ploy is to position your router away from the floor,
and as far from walls as is practical; otherwise, it will be surrounded by
reflected signals. When it comes to finer positioning, you can use
WifiInfoView, mentioned above, to test the strength of the signal in a given
part of your home, and experiment with repositioning the router (or other items
around your home) to see if any particular arrangement improves matters.
You can also try to upgrade your antenna
to give it a better reach. You’ll find various tutorials online showing how to
build a reflector out of an old beer can, or out of tinfoil, which can
help focus the signal towards your devices. If you don’t mind spending a bit of
money, you can replace your router’s antennas altogether with a larger aerial
on a cable. These are often advertised as “high gain”, but the benefit isn’t
really increased signal strength – rather it’s the fact that it’s easy to
position such an antenna wherever you want, while keeping your router tucked
away somewhere more convenient.
5.
Hacking your wireless router
Another way to make the signal from your
router carry further is to make it transmit more strongly. Typically, a
domestic router will ship with a fixed transmission power of 70mW, and while
you may be able to turn this down (to make it harder for people to piggyback
on your network from afar), you can’t normally turn it up.
For the technically inclined, however, all
things are possible. On a huge number of routers especially older 802.11n
models it’s possible to replace the built-in firmware with the free,
open-source DD-WRT. This provides access to a wide range of settings that
aren’t offered directly by the manufacturer, including the ability to ramp up
the signal strength all the way to 250mW.
Of course, there’s no such thing as a free
lunch. Flashing third-party firmware onto a router carries risks and good luck
getting the manufacturer to help you if anything goes wrong. Bear in mind, too,
that you’re tweaking only the strength of the signal from the router your
mobile devices will still be transmitting at their default signal strengths, so
this won’t necessarily do much for transfer speeds between them.
A final, rather important point is that
turning up the signal strength to maximum may cause your router to
overheat and crash. So if you want to try this hack, keep your router somewhere
cool, and proceed with caution.
6.
Upgrade to 802.11ac
The measures we’ve mentioned so far aim to
squeeze the best possible performance out of your existing wireless network,
but if you’re not already using the latest 802.11ac technology, upgrading is
likely to be the single most effective thing you can do to accelerate your
network. Where 802.11n has a theoretical maximum connection speed of
600Mbits/sec, the latest 802.11ac routers push the limit up to 2.3Gbits/sec.
Of course, you shouldn’t expect to see
those speeds in real-world use. These figures assume perfectly matched hardware
in perfect communication conditions, which you won’t get even if you position
your laptop directly on top of the router. All the same, you can expect to see
a significant boost simply from making the switch.
Buying a state-of-the-art router costs
money our current A-List favourite, the superfast Netgear R7500 Nighthawk X4,
won’t leave you much change from £200. And only laptops and other devices
that support the full speeds of 802.11ac will benefit. Most recent models will,
but check before you invest.
7.
Is wireless the answer?
Our final recommendation may sound like a
trick question: “What’s the best way to improve your wireless performance?
Don’t use wireless.” But if you want to hook up a PC to a router located at the
opposite end of your home, there may be better options than Wi-Fi. The obvious
alternative is powerline networking, which lets you run a wired Ethernet
connection between two or more domestic power sockets, with no need to trail
messy cables down the corridor.
It’s not the perfect solution, however.
Not all devices support wired Ethernet smartphones and tablets certainly
don’t. What’s more, mains circuits are inherently very noisy, and the signal
degrades sharply over distance. Current home plugs may advertise a maximum
transfer speed of 300Mbits/sec over a Gigabit Ethernet connection, but if
you’re connecting across several rooms then 60Mbits/sec is a more realistic
expectation.
A compromise might be to invest in
a powerline-based wireless extender. This lets you run a
powerline connection from your router to another part of the house,
and host a wireless network from there. The powerline run won’t be as
fast as a direct Ethernet connection, -but if the location of your
phone socket obliges your router to reside in a remote corner of the
house, such an approach might be your best option.
No comments:
Post a Comment